Olympia Chimney Chimney Cap Installation Nationwide

Olympia Chimney Chimney Cap Installation: The Mount Vernon Owner’s Guide

Olympia Chimney chimney cap installation in Mount Vernon typically runs $280-$520 for most single-flue residential caps, including removal of the damaged unit, fitting the replacement, and sealing the base. We stock common Olympia Chimney cap sizes on our trucks and can usually complete the job in one visit. Most Mount Vernon homeowners discover the problem after a storm, when water starts hitting the firebox floor, or when they notice rust stains weeping down the brickwork from the crown.

Call (914) 246-5794

Which Olympia Chimney Models This Applies To

Olympia Chimney manufactures caps across several product lines, and the right match depends on your flue type and existing chase cover or crown configuration. Their stainless steel single-flue caps fit standard clay flue tiles measuring 8×8, 8×13, or 13×13 inches, while multi-flue caps are sized to the overall chase top dimensions rather than individual flues. We see the 304-grade stainless models most often in Mount Vernon homes built between 1960 and 1990, particularly the raised-seam caps that mount with tension screws inside the flue tile.

To identify your cap, look for the small laser-etched Olympia Chimney logo on the skirt or cross-break top. If corrosion has eaten through that marking, measure the flue tile opening and note whether your cap sits inside the flue (tension-mount) or over it (outside-mount with screws through the skirt). Getting this wrong means a cap that either won’t seat or blows off in the first nor’easter. We carry both OEM Olympia Chimney caps and equivalent-grade Gelco and Copperfield units when the original series has been discontinued. Hearthstone Chimney Co. is an independent service provider, not affiliated with Olympia Chimney.

Signs Your Olympia Chimney Chimney Cap Is Failing

• Water on the firebox floor after rain. The cap’s mesh screen or lid has separated from the skirt, or the base seal has cracked. Once water gets past the cap, it runs down the flue and pools where the smoke chamber meets the firebox.
• Rust stains running down the chimney face. On galvanized or lower-grade caps, the finish fails and oxidation bleeds onto the brick or siding. In Mount Vernon, we see this accelerate where capillary action draws moisture from the Hudson’s humid air.
• Mesh screen pulled away or missing entirely. Squirrels and starlings force their way through weakened mesh to nest. The screen’s job is keeping animals out while letting smoke escape; a gap the width of a thumb is enough for a determined gray squirrel.
• Cap sitting crooked or visibly loose. Wind gusts off Long Island Sound - common in Mount Vernon, especially near the Hutchinson River Parkway corridor - can torque a poorly seated cap. Once the seal breaks, the cap becomes a sail.
• Spalling brick or deteriorating mortar at the crown. A failed cap lets water saturate the crown concrete, which freezes and thaws through Westchester winters. The damage you see below started at the top.

Replacement Cost & What’s Included

What moves the needle: height of roof access, whether the crown needs resurfacing before the new cap seats flat, and if the flue tile itself has cracked and needs stabilization first. We photograph the crown condition during our level-2 inspection and show you before we quote. The price we agree to is the price on the invoice. Every cap installation carries our 90-Day Done Right Promise in writing.

DIY or Call Us?

A homeowner can safely check whether the cap is loose from ground level with binoculars, and can clear light debris from the firebox. That’s where safe DIY ends.

Chimney cap replacement requires working at roof height on a sloped surface, often with tools in hand and both arms engaged. The cap itself isn’t the danger; the fall is. We’ve responded to Mount Vernon calls where a homeowner started the job, discovered the old cap was seized to the flue tile, and called us from the ladder. Don’t be that call. Our technicians are background-checked, uniformed, and carry the right torque drivers and high-temp sealants on every truck. Most Olympia Chimney cap swaps take under 90 minutes once we’re on the roof.

If it needs doing, we’ll tell you. If it doesn’t, we’ll tell you that too. Call (914) 246-5794 for a free estimate.

FAQs